ONX Engineering Tools

Ballscrew Sizing Calculator

Enter the ballscrew, load, acceleration, and motor-gear parameters to instantly see total force, reflected inertias, screw speed, motor speed, required torque, and power. Send the results to ONX Control engineers to request a custom solution for your application.

Start Calculation
Linear Speed
v → nbs
Total Force
FT = Fw+Ff+Fa
Screw Torque
T = pF / 2πη
Inertia Ratio
Λ = Jref / Jm
ONX ONX m F μ p Js Jc θ © 2026 ONX Control. All rights reserved. This animation may not be copied or reused without permission. Source: https://www.onxcontrol.com/en/calculators/lead-screw ONX Control ONX Control · https://www.onxcontrol.com © 2026 ONX Control. All rights reserved. This animation may not be copied or reused without permission. Source: https://www.onxcontrol.com/en/calculators/lead-screw https://www.onxcontrol.com/en/calculators/lead-screw ONX-34010593 © ONX Control · onxcontrol.com
JL = m·(p / 2π)² + Js + Jc T = (F + m·g·(sinθ + μ·cosθ))·p / (2π·η)
  • mMoving mass (load + carriage)
  • pLead: travel per screw revolution
  • JsScrew inertia
  • JcCoupling inertia
  • μGuide friction coefficient
  • FOpposing force (process, thrust)
  • θIncline angle (90° for vertical axis)

Ballscrew Geometry

Mechanical
°
mm/rev
mm
mm

Load and Motion Profile

Dynamic
kg
m/s
s
The engine calculates the total linear force as FT = Fw + Ff + Fa. If the total force is negative, the system may tend to overhaul / backdrive in the positive motion direction.

Motor and Gearbox Parameters

Drive
rpm
kg·cm²
Motor to screw connection

Most servo axes drive the screw directly through a coupling.

Suggested Ratio 0.00 : 1

 

System Forces

N
Gravity Force
0.00 N
Friction Force
0.00 N
Acceleration Force
0.00 N
Total Force
0.00 N

Inertia Values

kg·cm²
Load Inertia
0.00
Screw Inertia
0.00
Total Inertia
0.00
Reflected to Motor
0.00

Kinematic Results

Velocity
Screw Angular Accel.
0.00 rad/s²
Screw Angular Vel.
0.00 rad/s
Screw Speed
0.00 rpm
Motor Speed
0.00 rpm

Motor Sizing

Drive
Screw Torque
0.00 Nm
Screw Torque w/ SF
0.00 Nm
Required Motor Torque
0.00 Nm
Motor Torque w/ SF
0.00 Nm
Required Motor Power
0.00 kW
Inertia Ratio
0.00
Visual analysis

The components of the axial force on the screw and the inertia ratio that matters for servo selection.

Live
Axial force components (N)
Load / motor inertia ratio
Motor speed use–

Engineering Expert Insight

Inertia ratio is a critical parameter: As the ratio of reflected load inertia to motor rotor inertia increases, tuning becomes difficult, and vibration/response issues may arise. This ratio should be carefully monitored, especially in highly dynamic applications.

Overhauling conditions must not be overlooked: If gravity makes the total force negative, the system may tend to backdrive while being driven in the positive direction. In this case, braking, regeneration, and holding strategies must be evaluated alongside motor torque.

How to Calculate Ballscrew Sizing?

Motor selection in ballscrew systems is not based solely on load weight. Incline, friction, acceleration time, screw lead, screw efficiency, gear ratio, and total reflected inertia must be evaluated together.

When converting a linear load to a rotary system, the total linear force is found first. This force is then converted to rotary torque via screw lead and efficiency. The next step is calculating the required motor torque and power, factoring in gear ratio and gear efficiency.

This calculator by ONX Control brings together force, inertia, screw speed, motor speed, required torque, and power values on a single screen, providing rapid pre-sizing for linear axes, Z-axes, servo presses, pick-and-place, and special machine applications.

Frequently Asked Questions

What is the most critical parameter in ballscrew sizing?

There is no single critical parameter. Lead, total load, acceleration time, and inertia ratio must be evaluated together.

What should the inertia ratio be?

It depends on the application. In servo systems, lower ratios are easier to tune. Ratios above 10 require more careful analysis of system behavior.

Does gearbox efficiency affect motor torque?

Yes. The torque required at the screw is seen by the motor as a higher input torque due to gearbox inefficiency.

Is this tool sufficient for final motor selection?

It is very useful for pre-sizing. However, for the final selection, duty cycle, rigidity, critical screw speed, resonance, braking, and safety factors must also be examined.